Thiết bị kiểm tra độ cách nhiệt vải GESTER GT-CN08

Lượt xem:
9111
Thương hiệu:
Gester - Trung Quốc
Giá:
Liên hệ

Thiết bị bảo vệ nhiệt TPP chủ yếu được sử dụng để đo hiệu suất cách nhiệt của vải quần áo bảo hộ chống cháy tiếp xúc với nguồn nhiệt bức xạ và nguồn nhiệt đối lưu để phát hiện hiệu suất bảo vệ nhiệt của quần áo bảo hộ, giày an toàn, găng tay và bề mặt ngoài của mũ bảo hiểm.
Tiêu chuẩn: NFPA 1971, ASTM D4018, GB 8965.1-2009, ISO 17492, GA etc.

Dệt May

Feature

The test equipment shall include the sample holder assembly, the holder of the sample holder assembly, the heat source, the protective cover, the sensor assembly, the recorder, and the gasket. It shall also have a gas source, a gas flow meter, a burner, and a sensor.
Removable corundum protection board, temperature 1800 degrees, can block the flame and reduce the test error.
Two 45-degree Meker burners were placed to provide standard convection heat sources with nine quartz tubes.
Meker burner diameter 38mm, internal hole diameter 5/16 inches, can provide 800-1200 BUT heat output, the burner mouth is a metal mesh structure, the burner lower air valve can be adjusted, adjustable air and flammable gas mixture proportion.
Nine T150 quartz IR arrays provide thermal radiation flux of 13-40 kW/m2 ± 4 kW/m2.
The total heat flux can be set to 83 kW/m2 ± 2 kW/m2 by adjusting the gas supplied to the Meker burner under the heat radiation of a quartz infrared tube.
The calibration heat flow meter is water-cooled, with a working range of 0-100 kW/m2 and a maximum range of 150%.
The response time of the heat flow meter is less than 200ms, the emissivity is greater than 0.95, and the output signal is greater than 5mv in the operating range.
The copper pan calorimeter device can be used to detect convective heat and radiant heat, while detecting the temperature of the back of the specimen.
The rotameter can adjust the flow of combustion gas with an accuracy of ±2% and a range of more than 3L/min.
The pointer pressure gauge, the inlet pressure can be adjusted through the pressure reducing valve, the pressure relief valve has a range of 0-15psi.
A quarter turn plug can manually shut off the flammable gas.
The temperature acquisition system has a resolution of 0.1C° and an accuracy of ±0.75°C.
The data acquisition speed of the automated data acquisition system is sub-/0.05 second and cold junction compensation is provided for thermocouple measurement data.
Equipped with computers and printers, comes with standard test software and provides standard test curves.

Key Specifications

Model	GT-CN08
Climate Requirements	Propane and compressor air
Test Environment	25±5℃
Holding Way	Pneumatic or manual
Power Supply	220V 50Hz 15A
Dimensions	1500×540×460mm ((W×H×D)
Weight	86kg
Standards	NFPA 1971, ASTM D4018, GB 8965.1-2009, ISO 17492, GA etc.

Tập tin PDF:

Sản phẩm cùng loại

Chi tiêt Xem nhanh

AUTOMATIC WASHING MACHINE AW-12

Hãng sx: RAPID (Labortex)

AW-12 is indispensable Lab equipment used for carrying out post-processing such as washing, scoring and soaping for dyed yarn, fabric or any textile samples. Users just need to place textile samples into stainless steel washing pots, then water adding, chemical dosing, washing as well as draining will be automatically processed by a programmable controller. Samples with solution can be gently agitated by air turbulence which is introduced by blowers, therefore, manual stirring is no longer required.

Liên hệ

Chi tiêt Xem nhanh

Laboratory ROLL MILL

Hãng sx: RAPID (Labortex)

Laboratory ROLL MILL is a compact model with lowest noise level, highest safety, its specially-designed electric heaters evenly and accurately radiate heat to achieve the required surface temperature according to the command given by two modernized temperature controllers.

Liên hệ

Chi tiêt Xem nhanh

AUTO COATING DEVICE

Hãng sx: RAPID (Labortex)

AUTO COATING, an indispensable device for laboratory coating process. For conventional coating process, the inconsistent speed and pressure always causes serious problem regarding uneven coating quality. Our AUTO COATING device is designed to fulfill in every coating necessity with the best reproducibility.

Liên hệ

Chi tiêt Xem nhanh

LABORATORY MINI OVEN

Hãng sx: RAPID (Labortex)

LABORATORY MINI OVEN is designed to be paired up with our AUTO COATING device. The integrated pin-frame is compatible with both machines; therefore, samples can be directly moved to this hot-air oven for drying treatment after coating without any re-pinning process.

Liên hệ

Chi tiêt Xem nhanh

Vertical type model P-AO

Hãng sx: RAPID (Labortex)

Vertical type model P-AO, this extremely versatile laboratory padding mangle is built as a floor model. High grade stainless steel construction. Ergonomically designed for fast, convenient use. Short samples as well as fabrics with a length of several meters can be easily dyed. Suitable for all dyeing, printing, finishing, and padding processes.

Liên hệ

Chi tiêt Xem nhanh

MINI TENTER

Hãng sx: RAPID (Labortex)

MINI TENTER, the Flexible Continuous pin chain type hot Air dryer, suitable for all applications where a certain sample length is required in a continuous process.

Liên hệ

Chi tiêt Xem nhanh

R-3

Hãng sx: RAPID (Labortex)

Table Model, Excellent laboratory dryer for all drying, setting, baking and thermosoling processes. The machine is designed to simulate the features of production scale stenter.

Liên hệ

Chi tiêt Xem nhanh

HT-Steamer H-TS-3

Hãng sx: RAPID (Labortex)

Saturated and HT-Steamer, suitable for the chemical and dyestuff industry, finishing plants, research institutes and general textile industry. Basic design as MINI-DRYER, model R-3, owing the wide adjusting ranges regarding temperature, humidity, dwelling time.

Liên hệ

Chi tiêt Xem nhanh

Máy rửa liên tục LAB WASHER

Hãng sx: RAPID (Labortex)

LAB WASHER phòng thí nghiệm, chủ yếu là 4 bể là thiết kế chính, có thể được sử dụng trong hoạt động của một máy hoặc kết hợp máy cán, hút, hấp và nhuộm liên tục PS-J hoặc PS-JS.

Liên hệ